Technical Presentations

Impact of Power Transformer Energization on Relay Protection Operation844

Abstract
One of the main causes of the incorrect operation of transformer relay protection are inrush currents. The transient inrush current occurs when energizing the unloaded transformer, and it is a consequ... see moreence of the transformer core saturation. This paper presents analysis of transients caused by energization of 300 MVA three-phase autotransformer with stabilizing winding and voltage ratios 400/115/10,47 kV.

Using the PAMSUITE Toolbox in EMTP, many simulations were performed to show the impact of model’s parameters on the amplitude and duration of inrush currents as well as the probability of 2nd harmonic differential current amplitude occurrence. Simulation results show that controlled switching reduces inrush currents amplitudes and increases 2nd harmonic content in differential currents. A Protection Toolbox in EMTP was used for modelling CT saturation and operation of transformer’s differential protection relay.

Based on the simulation results the optimal differential protection settings were determined, and the probability of false relay protection operation was calculated.

Tag(s): transformer, energization, inrush, differential, protection, harmonics, bctran, pamsuite

Optimization of Control Parameters of Grid-Connected PV System in EMTP845

Abstract
It is observed that the controller gain parameters of the PV model have a significant impact on the PV plant’s response during the fault recovery and the PV plant’s interaction with the rest of th... see moree system in general. Manual tuning of the PV park parameter considering multiple fault and contingency scenarios is a time-consuming task and might even be impossible. Optimization techniques such as particle swarm optimization (PSO) can be used to optimize the gain parameters considering fault/ contingency scenarios. The presentation will talk about the implementation of PSO in EMTP using javascript to optimize PV park controller gain parameters.

Tag(s): pv plant, ibr, pso, optimization, scripting, pll, inverter control, inverter based resources, DER

Measurement and EMTP Simulation of Ferroresonance Phenomenon849

Abstract
Ferroresonance is difficult to predict because its occurrence in the power system depends on several parameters, some of which are unknown (parasitic capacities). In addition, measuring electrical con... see moreditions during high voltage ferroresonance is very difficult to achieve. In order to check the possibilities of numerical calculations of ferroresonance, the ferroresonant circuit was made as a low voltage circuit in which all parameters were known.

Measurement of ferroresonant current and voltages in a single-phase low voltage circuit will be described. The system consists of an AC voltage source, a capacitor, a switch and the single-phase transformer. These electrical elements are connected in series. The magnetic flux-current points of the magnetization curve of the transformer was experimentally obtained and used in the simulation. When the switch closes, ferroresonance takes place since all conditions were met for its occurrence. The waveforms of the transformer current and the voltage at the transformer terminals were measured after switch closing.

During the ferroresonance, transformer voltage and current reach relatively high values. At the beginning of the ferroresonance (during its transient part), the voltage of the transformer reaches values that are about two times higher in amplitude than the amplitude of the AC source. The primary side of the transformer was modelled with a series connection of the ohmic resistance and leakage inductance. The core was modelled with a parallel connection of the ohmic resistance and nonlinear inductance. The ohmic resistance represents the core losses while the nonlinear inductance models the magnetizing characteristic of the transformer.

A comparison between simulated and experimentally obtained results shows that EMTP successfully simulates the ferroresonance phenomenon for this specific electrical system as simulated results are in a good agreement with the measured results.

Tag(s): ferroresonance, tov, saturation

EMTP Development Roadmap: PSS/E Import Tool in EMTP 4.2830

Abstract
1. Custom device usage
- New option which allows to import a user-defined device
- Scripts may be called to process the parameters of the RAW, SEQ and DYR files
- The user customer devi... see moreces file section provides the interface

2. Import only specific part of a grid
- This new option allows user to import only specific parts of the RAW file
- PSS/E is required to use this option

Tag(s): EMT simulation, PSSE, grid, import tool

Modeling and evaluation of overvoltage792

Abstract
A case study will be presented demonstrating modeling of overvoltage in a moderately sized system involving medium voltage vacuum breakers, cables and transformers. The focus is on simulating high fre... see morequency overvoltage generated by circuit breaker prestrikes and re-ignitions and evaluating the impacts on transformer insulation.
-Results obtained from a customized breaker TRV model which is capable of controlling the capability of switching high frequency current will be presented.
-The methodology of analyzing severity of overvoltage in the frequency domain was applied in this project. Results and discussions regarding frequency domain analysis will be shared.
-Simulation results regarding typical system configurations with variation of key parameters such as cable lengths, load power factors will be briefly presented.
-Application of EMTP study results in assisting equipment specification, as well as overvoltage mitigation methods including optimizing switching sequences, necessity of snubber circuits will be discussed.
-Case specific strategies to improve simulation speed and work flow with EMTP will be introduced and discussed.